- Oct 04, 2011
-
-
git://git.denx.de/u-boot-mpc85xxWolfgang Denk authored
* 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/p3060: Add SoC related support for P3060 platform powerpc/85xx: Add support for setting up RAID engine liodns on P5020 powerpc/85xx: Refactor some defines out of corenet_ds.h fm-eth: Add ability for board code to disable a port powerpc/mpc8548: Add workaround for erratum NMG_LBC103 powerpc/mpc8548: Add workaround for erratum NMG_DDR120 powerpc/mpc85xxcds: Fix PCI speed powerpc/mpc8548cds: Fix booting message powerpc/p4080: Add support for secure boot flow powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards powerpc/p2041rdb: remove watch dog related codes powerpc/p2041rdb: updated description of cpld command powerpc/p2041rdb: add more ddr frequencies support powerpc/p2041rdb: set sysclk according to status of physical switch SW1 powerpc/p2041rdb: update cpld reset command according to CPLD 2.0 powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver powerpc/mpc8xxx: Add DDR2 to unified DDR driver powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps() powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en powerpc/85xx: Refactor P2041RDB to use common p_corenet files powerpc/85xx: refactor common P-Series CoreNet files for FSL boards powerpc/85xx: Enable CMD_REGINFO on corenet boards powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries powerpc/85xx: Fix USB protocol definitions for P1020RDB powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM powerpc/mpc8xxx: Move DDR RCW overriding to common code powerpc/mpc8xxx: Extend CWL table powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536 powerpc/85xx: Cleanup extern in corenet_ds board code powerpc/p2041rdb: Add ethernet support on P2041RDB board powerpc/85xx: Add networking support to P1023RDS powerpc/hydra: Add ethernet support on P5020/P3041 DS boards powerpc/85xx: Add FMan ethernet support to P4080DS powerpc/85xx: Add support for FMan ethernet in Independent mode powerpc/mpc8548cds: Cleanup mpc8548cds.c powerpc/mp: add support for discontiguous cores powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries fdt: Add new fdt_create_phandle helper fdt: Rename fdt_create_phandle to fdt_set_phandle powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010) powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC) fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010) powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB nand: Freescale Integrated Flash Controller NAND support powerpc/85xx: Add basic support for P1010RDB powerpc/85xx: Add support for new P102x/P2020 RDB style boards powerpc/85xx: relocate CCSR before creating the initial RAM area powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
-
git://git.denx.de/u-boot-i2cWolfgang Denk authored
* 'master' of git://git.denx.de/u-boot-i2c: I2C: mv_i2c: fix multi-bus init issue I2C: mv_i2c: fix build issue when enable debug option
-
git://git.denx.de/u-boot-microblazeWolfgang Denk authored
* 'emaclite' of git://git.denx.de/u-boot-microblaze: net: emaclite: Use dynamic allocation net: emaclite: Remove baseaddress from xemaclite net: emaclite: Use calloc instead of malloc net: emaclite: Remove deviceid property net: emaclite: Change driver name and add address
-
git://git.denx.de/u-boot-microblazeWolfgang Denk authored
* 'master' of git://git.denx.de/u-boot-microblaze: microblaze: Enable FDT/FIT support microblaze: Remove address offset for uart16550 microblaze: Do not select NFS for platforms without ethernet microblaze: Clean up reset asm code microblaze: Save and restore first unused vector microblaze: Setup MB vectors if feature is enable for u-boot microblaze: Remove debug saving value
-
Wolfgang Denk authored
This reverts commit 60ce53cf. The commit causes build breakage for a number of boards. This results from the fact that now the arguments of debug() actually get referenced (even if there is hope that the compiler will optimize away the debug() call). The obvious fix to that probem (change the code to always declare the referenced variables and data structures) increases the code size, and was this rejected. So it was decided to revert this commit until a better solution is found.
-
- Oct 03, 2011
-
-
Shengzhou Liu authored
Add P3060 SoC specific information:cores setup, LIODN setup, etc The P3060 SoC combines six e500mc Power Architecture processor cores with high-performance datapath acceleration architecture(DPAA), CoreNet fabric infrastructure, as well as network and peripheral interfaces. Signed-off-by:
Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by:
Kumar Gala <galak@kernel.crashing.org>
-
Kumar Gala authored
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2 Rings per JQ). This just handles RAID Engine in non-DPAA mode. Signed-off-by:
Santosh Shukla <santosh.shukla@freescale.com> Signed-off-by:
-
Kumar Gala authored
Move some SoC/board specific defines out of corenet_ds.h and into the corresponding P3041DS/P4080DS/P5020.h. We moved CONFIG_MMC, CONFIG_PCIE3, & CONFIG_FSL_NGPIXIS because the P3060 SoC/reference board does not have these devices and it will share the same board code. Signed-off-by: -
Kumar Gala authored
The SoC configuration may have more ports enabled than a given board actually can utilize. Add a routinue that allows the board code to disable a port that it knows isn't being used. fm_disable_port() needs to be called before cpu_eth_init(). Signed-off-by: -
Kumar Gala authored
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document. Any local bus transaction may fail during LBIU resynchronization process when the clock divider [CLKDIV] is changing. Ensure there is no transaction on the local bus for at least 100 microseconds after changing clock divider LCRR[CLKDIV]. Refer to the erratum LBIU3 of mpc8548. Signed-off-by:
Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by:
-
Kumar Gala authored
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some early version silicons. The default settings of the DDR IO receiver biasing may not work at cold temperature. When a failure occurs, a DDR input latches an incorrect value. The workaround will set the receiver to an acceptable bias point. Signed-off-by: Gong Chen Signed-off-by:
-
chenhui zhao authored
The CDS uses PCICLK as SYSCLK. The PCICLK should be 33333333Hz or 66666666Hz. Signed-off-by:
Ebony Zhu <ebony.zhu@freescale.com> Signed-off-by:
-
chenhui zhao authored
Align the output for PCI. Replace "PCI" with "PCI1". Signed-off-by: -
Ruchika Gupta authored
Pre u-boot Flow: 1. User loads the u-boot image in flash 2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000 (Please note that ISBC expects all these addresses, images to be validated, entry point etc within 0 - 3.5G range) 3. ISBC validates the u-boot image, and passes control to u-boot at 0xcffffffc. Changes in u-boot: 1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M CONFIG_SYS_PBI_FLASH_WINDOW in AS=1. (The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash created by PBL/configuration word within 0 - 3.5G memory range. The u-boot image at this address has been validated by ISBC code) 2. Remove TLB entries for 0 - 3.5G created by ISBC code 3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by PBL/configuration word after switch to AS = 1 Signed-off-by:Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by:
Kuldip Giroh <kuldip.giroh@freescale.com> Acked-by:
Wood Scott-B07421 <B07421@freescale.com> Signed-off-by:
-
Ruchika Gupta authored
Signed-off-by:
-
Kumar Gala authored
Signed-off-by: -
Shaohui Xie authored
CPLD 2.2 removed board watch dog support due to the limitation of CPLD capacity after adding all the requested features, such as switch overriding. There is no pin-compatible upgrade part available for current PCB design. So remove codes related to it. Signed-off-by:
Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by:
-
Shaohui Xie authored
According to CPLD 2.2, the default configuration is changed, so updated the description of CPLD command, otherwise it will confusing. Signed-off-by:
-
Shaohui Xie authored
This table covers DDR frequencies from 666 to 1666. Frequencies 666, 833, 1000, 1066 and 1333 were verified on this board with SO-DIMM (UG51U6400N8SU-ACF). Signed-off-by:
-
Shaohui Xie authored
P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8], software need to read the SW1 status to decide what the sysclk needs. SW1[8~6] : frequency 0 0 1 : 83.3MHz 0 1 0 : 100MHz others: 66.667MHz Signed-off-by:
-
Shaohui Xie authored
CPLD 2.0 provides a new register which bit[0] is set to '1' will reset board with initializing the CPLD registers to default values. And add bit[6] of register at offset 0x5 to use to enable flash bank selection. Signed-off-by:
-
Lei Wen authored
When enable the multi-bus, the current_bus is not inited in the original implementation, which make the i2c operation unpredicatable. Signed-off-by:Lei Wen <leiwen@marvell.com>
-
Lei Wen authored
When DEBUG_I2C is open, the following build issue would shows up. mv_i2c.c: In function 'i2c_transfer': mv_i2c.c:257: error: 'ISR' undeclared (first use in this function) mv_i2c.c:257: error: (Each undeclared identifier is reported only once mv_i2c.c:257: error: for each function it appears in.) Signed-off-by: -
Michal Simek authored
Every emaclite instance use own setting. Signed-off-by:
Michal Simek <monstr@monstr.eu> Acked-by:
Mike Frysinger <vapier@gentoo.org>
-
Michal Simek authored
Use dev->iobase instead of baseaddress. Signed-off-by: -
Michal Simek authored
Simplify driver logic and clear eth_device structure in one command. Signed-off-by: -
Michal Simek authored
Cleanup structure. Signed-off-by: -
Michal Simek authored
Current xilinx emaclite use net multi registration but doesn't support several emaclites interfaces. Changing driver name with adding address to name is the first step how to distiguish several drivers. Signed-off-by: -
Michal Simek authored
Enable FDT and FIT support. Signed-off-by: -
Michal Simek authored
U-Boot BSP handle 0x3 offset for big endian systems. Little endian Microblaze systems don't use any offset. Signed-off-by: -
Michal Simek authored
Undefined network functionality for systems without ethernet and disable NFS support. Signed-off-by: -
Michal Simek authored
- Remove code copying - Reset address is setup from first stage bootloader - Support reset vector setup on little endian Signed-off-by: -
Michal Simek authored
Use one memory space to detect little/big endian platforms. The first unused address(0x28) is used instead 0x0 address (reset vectors). Detection rewrited reset vector setup from first stage bootloader. Workflow: 1. Store 0x28 to r7 2. Do little/big endian test 3. Restore r7 to 0x28 Signed-off-by: -
Michal Simek authored
For example: Setup reset vectors if reset address is setup. Setup user exception vector if user exception is enabled Signed-off-by: -
Michal Simek authored
Forget to remove debug code. Signed-off-by:
-
- Oct 01, 2011
-
-
Marek Vasut authored
lzo1x_decompress.c: In function ‘parse_header’: lzo1x_decompress.c:35:5: warning: variable ‘level’ set but not used [-Wunused-but-set-variable] Signed-off-by:
Marek Vasut <marek.vasut@gmail.com> Acked-by:
-
Marek Vasut authored
cmd_ubi.c: In function ‘ubi_volume_read’: cmd_ubi.c:319:9: warning: variable ‘count_save’ set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Marek Vasut authored
vmt.c: In function ‘ubi_free_volume’: vmt.c:681:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Marek Vasut authored
cmd_nand.c: In function ‘do_nand’: cmd_nand.c:490:7: warning: variable ‘chip’ set but not used [-Wunused-but-set-variable] cmd_nand.c:489:7: warning: variable ‘part’ set but not used [-Wunused-but-set-variable] Signed-off-by:
-
Marek Vasut authored
nand_bbt.c: In function ‘search_bbt’: nand_bbt.c:465:6: warning: variable ‘bits’ set but not used [-Wunused-but-set-variable] Signed-off-by:
-
