Add config to support bank address register.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Yebio Mesfin <ymesfin@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

The RDY bit indicates that a transfer is complete. This needs to be
cleared by SW before every single HW transaction, rather than only
at the start of each SW transaction (those being made up of n HW
transactions).

It seems that earlier HW may have cleared this bit autonomously when
starting a new transfer, and hence this code was not needed in practice.
However, this is generally a good idea in all cases. In Tegra124, the
HW behaviour appears to have changed, and SW must explicitly clear this
bit. Otherwise, SW will believe that transfers have completed when they
have not, and may e.g. read stale data from the RX FIFO.

Signed-off-by: Yen Lin <yelin@nvidia.com>
[swarren, rewrote commit description, unified duplicate RDY clearing code
and moved it right before the start of the HW transaction, unconditionally
exit loop after reading RX data, rather than checking if TX FIFO is empty,
since it is guaranteed to be]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

This patch adds a driver for Renesas SoC's Quad SPI bus.
This supports with 8 bits per transfer to use with SPI flash.

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

Add support for Macronix MX25L2006E SPI flash.

Signed-off-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

All other hex values in sf_probe.c are in lower case so we should
fix this one too.

Signed-off-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

SH7753 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The SH7753 EVB board has SH7753, 512MB DDR3-SDRAM, SPI ROM,
Gigabit Ethernet, and eMMC.

This patch support the following functions:
 - 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Commit fea25720 renamed arch/i386 to arch/x86.
But it missed to modify examples/standalone/Makefile.

Since then, examples/standalone/82559_eeprom has
never compiled and nobody has noticed that.

After some discussion on ML, we agreed to delete this example.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Convert like follows:

 CPU mpc83xx  -> CONFIG_MPC83xx
 CPU mpc85xx  -> CONFIG_MPC85xx
 CPU mpc86xx  -> CONFIG_MPC86xx
 CPU mpc5xxx  -> CONFIG_MPC5xxx
 CPU mpc8xx   -> CONFIG_8xx
 CPU mpc8260  -> CONFIG_8260
 CPU ppc4xx   -> CONFIG_4xx
 CPU x86      -> CONFIG_X86
 ARCH x86     -> CONFIG_X86
 ARCH powerpc -> CONFIG_PPC

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

REMOTE_BUILD is not used any more.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Miao Yan <miao.yan@windriver.com>

fdt_fixup_memory_banks() will add and update /memory node in
device tree blob. In the case that /memory node doesn't exist,
after adding a new one, this function returns error.

The correct behavior should be continuing to update its properties.

Signed-off-by: Miao Yan <miao.yan@windriver.com>

The next version VxWorks adopts device tree (for PowerPC and ARM) as its hardware
description mechanism. For PowerPC, the boot interface conforms to
the ePAPR standard, which is:

   void (*kernel_entry)(ulong fdt_addr,
          ulong r4 /* 0 */,
          ulong r5 /* 0 */,
          ulong r6 /* EPAPR_MAGIC */, ulong r7 /* IMA size */,
          ulong r8 /* 0 */, ulong r9 /* 0 */)

For ARM, the boot interface is:

   void (*kernel_entry)(void *fdt_addr)

Signed-off-by: Miao Yan <miao.yan@windriver.com>
[trini: Fix build error when !CONFIG_OF_FDT is set, typo on PowerPC,
missing extern ft_fixup_num_cores]
Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Miao Yan <miao.yan@windriver.com>

do_bootm_vxworks now is available under the configuration option
CONFIG_BOOTM_VXWORKS, thus aligned with other operating systems
that supported by bootm command. The bootvx command still depneds
on CONFIG_CMD_ELF.

Signed-off-by: Miao Yan <miao.yan@windriver.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

We have some scripts imported from Linux Kernel:
setlocalversion, checkstack.pl, checkpatch.pl, cleanpatch

They are located under tools/ directory in U-Boot now.
But they were originally located under scripts/ directory
in Linux Kernel.

This commit moves them to the original location.

It is true that binutils-version.sh and dtc-version.sh
do not originate in Linux Kernel, but they should
be moved by analogy to gcc-version.sh.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Before switching to the real Kbuild, drivers/usb/gadget/Makefile
must be fixed.
If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE
is defined, both obj- and obj-y get empty.

We need non-empty obj- or obj-y on each Makefile
to generate built-in.o on the real Kbuild.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

All objects under post/ directory are enabled by CONFIG_HAS_POST.
(post/tests.o is enabled by CONFIG_POST_STD_LIST.
But CONFIG_POST_STD_LIST depends on CONFIG_HAS_POST.)

We can move CONFIG_HAS_POST switch to the top Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

$(LDSCRIPT) is a source file, not a generated file.
We do not need a make rule of $(LDSCRIPT).

And one more trivial fix:
$(obj)/u-boot should not dierectly depend on $(LDSCRIPTS).

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

If U-Boot build with DEBUG enabled/defined the first call of "debug"
function (that dumps data to any available console) will happen before
zeroing of initial "gd" in init call "zero_global_data" in
"init_sequence_f".

And if stack was not filled with zeros chances are high that
"gd->have_console" won't be 0. In its turn it will cause attempt to
output things to non-initialized yet serial console.

So for safety and predictability we set "gd->have_console = 0".

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

argv[0] contains bootvx (command name) not the load address, if called with
argv < 2 use load_addr, else use address argument given to the command.

Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com>

Before this commit, output files under tpl/ directry
were not ignored.
This commit fixes this problem.

And we have only one source file under spl/ directory:
 spl/Makefile

So, we can describe .gitignore more simply.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

PLATFORM_RELFLAGS += -meabi
PLATFORM_CPPFLAGS += -ffixed-r2
were defined in all arch/powerpc/${CPU}/config.mk.

This commit moves them to arch/powerpc/config.mk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

The documentation suggested the arguments where passed over r3-r6
while the code below simply does that over r0-r3.

Cc: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Tom Rini <trini@ti.com>

Since part_info size became 64bit we need to use lldiv here.

Signed-off-by: Tom Rini <trini@ti.com>