Add following debug information in the driver
 - Get various DPNI counter values
 - Get link status of DPNI objects
 - Get information of both ends of connection (DPMAC - DPNI)

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

As per current implementation of DPAA2 ethernet driver DPNI is used as
net device. DPNI is tangible objects can be multiple connected to same physical lane.

Use DPMAC as net device where it represents physical lane.
Below modification done in driver
 - Use global DPNI object
 - Connect DPMAC to DPNI
 - Create and destroy DPMAC

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.

Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.

Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

dpni_create API take takes more time as comapred to existing supported
APIs of MC Flib.
So increase MC command timeout.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

DPMAC represents physical line on the board. This physical
line eventually asscociate with on-board PHY.

So Add an api to return linked PHY ID of DPMAC object.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Print function name along with SerDes Protocol during SerDes Protocol
not supported error.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

DPMAC object of Management complex controls Physical MAC and MDIO controller.
It provides APIs for MDIO and link state updates. It also provides APIs for
PHY/link configuration.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Current Management Complex Flibs does not support APIs for adding and
destroying the objects.

Add APIs to create and destroy objects for DPBP, DPIO, DPNI and DPRC.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.

Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

This patch addresses a problem mentioned recently on this mailing list:
[1].

In that posting a LS1021 based system was locking up at about 5 minutes
after boot,but the problem was mysteriously related to the toolchain
used for building u-boot.Debugging the problem reveals a stuck
interrupt 29 on the GIC.

It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.This causes the timer compare to fire 344 seconds
after u-boot configures it.Depending on how fast u-boot gets the
kernel booted,this amounts to about 5-minutes of Linux uptime before
locking up.

Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.

To fix the above issue, the generic physical timer is disabled
before jumping to the OS.

[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html



Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: York Sun <yorksun@freescale.com>

This patch addresses a problem mentioned recently on this mailing list:
[1].

In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot.  Debugging the problem reveals a stuck
interrupt 29 on the GIC.

It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.  This causes the timer compare to fire 344 seconds
after u-boot configures it.  Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.

Apparently the bug is masked by some toolchains.  Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.

[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html



Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Use the correct function name in the function description.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>

Enabling the new tiny-printf function makes the SPL image fit again in
the 8KiB restricted area.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>

There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().

Tested on AM437x IDK EVM with QSPI XIP boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

If the ext3 journal gets out of sync with what is written on disk, for
example because of an unexpected power cut, ext4fs_read_file can
return an all-zero directory entry.  In that case, ext4fs_iterate_dir
would infinite loop.

This patch detects when a directory entry's direntlen member is 0 and
returns a failure status, which breaks out of the infinite loop.  As a
result, U-Boot will not find files that may subsequently be recovered
when the journal is replayed.

This is better behaviour than hanging in an infinite loop, but as a
further improvement maybe U-Boot could interpret the ext3 journal and
actually find the unsynced entries.

Signed-off-by: Thomas Fitzsimmons <fitzsim@cisco.com>
Reviewed-by: Stefan Roese <sr@denx.de>

The address range check may overflow if the memory region is located at
the top of the 32-bit address space. This can e.g. be seen on TK1 if
using the E1000 gigabit Ethernet driver where start and size are both
0x80000000 leading to the following messages:

Apalis TK1 # tftpboot $loadaddr test_file
Using e1000#0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.2
Filename 'test_file'.
Load address: 0x80408000
Loading: pci_hose_phys_to_bus: invalid physical address

This patch fixes this by changing the order of the addition vs.
subtraction in the range check just like already done in
__pci_hose_bus_to_phys().

Reported-by: Ivan Mercier <ivan.mercier@nexvision.fr>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

The optional parameter bootable is added in gpt command to set the
partition attribute flag "Legacy BIOS bootable"

This flag is used in extlinux and so in with distro to select
the boot partition where is located the configuration file
(please check out doc/README.distro for details).

With this parameter, U-Boot can be used to create the boot partition
needed for device using distro.

example of use:

setenv partitions "name=u-boot,size=60MiB;name=boot,size=60Mib,bootable;\
                   name=rootfs,size=0"

> gpt write mmc 0 $partitions

> part list mmc 0

Partition Map for MMC device 0  --   Partition Type: EFI

Part	Start LBA	End LBA		Name
	Attributes
	Type GUID
	Partition GUID
  1	0x00000022	0x0001e021	"u-boot"
	attrs:	0x0000000000000000
	type:	ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
	guid:	cceb0b18-39cb-d547-9db7-03b405fa77d4
  2	0x0001e022	0x0003c021	"boot"
	attrs:	0x0000000000000004
	type:	ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
	guid:	d4981a2b-0478-544e-9607-7fd3c651068d
  3	0x0003c022	0x003a9fde	"rootfs"
	attrs:	0x0000000000000000
	type:	ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
	guid:	6d6c9a36-e919-264d-a9ee-bd00379686c7

> part list mmc 0 -bootable devplist

> printenv devplist

devplist=2

Then the distro scripts will search extlinux in partition 2
and not in the first partition.

Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

This commit adds support for "gpt verify" command, which verifies
correctness of on-board stored GPT partition table.
As the optional parameter one can provide '$partitons' environment variable
to check if partition data (size, offset, name) is correct.

This command should be regarded as complementary one to "gpt restore".

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>

This commit provides definition and declaration of GPT verification
functions - namely gpt_verify_headers() and gpt_verify_partitions().
The former is used to only check CRC32 of GPT's header and PTEs.
The latter examines each partition entry and compare attributes such as:
name, start offset and size with ones provided at '$partitions' env
variable.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>

./doc/README.gpt entry has been updated to explain usage of "gpt verify"
command.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>

Exactly the same check is performed in set_gpt_info() function executed
just after this check.

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>

With this patch now, the tiny printf() function also supports numbers
bigger than 0xffff. Additionally the code is simplified a bit and
some static variables are moved to function parameters. Also the
upper case hex variable output support is removed, as its not really
needed in this simple printf version. And removing it reduces the
complexity and the code size again a bit.

Here the new numbers, again on the db-mv784mp-gp (Armada XP):

Without this patch:
  56542   18536    1956   77034   12cea ./spl/u-boot-spl

With this patch:
  56446   18536    1936   76918   12c76 ./spl/u-boot-spl

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

This patch adds a small printf() version that supports all basic formats.
Its intented to be used in U-Boot SPL versions on platforms with very
limited internal RAM sizes.

To enable it, just define CONFIG_USE_TINY_PRINTF in your defconfig. This
will result in the SPL using this tiny function and the main U-Boot
still using the full-blown printf() function.

This code was copied from:
http://www.sparetimelabs.com/printfrevisited


With mostly only coding style related changes so that its checkpatch
clean.

The size reduction is about 2.5KiB. Here a comparison for the db-mv784mp-gp
(Marvell AXP) SPL:

Without this patch:
  58963   18536    1928   79427   13643 ./spl/u-boot-spl

With this patch:
  56542   18536    1956   77034   12cea ./spl/u-boot-spl

Note:
To make it possible to compile tiny-printf.c instead of vsprintf.c when
CONFIG_USE_TINY_PRINTF is defined, the functions printf() and vprintf() are
moved from common/console.c into vsprintf.c in this patch.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

Change some comments to match the U-Boot coding style rules.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

As done in commit da229e4e [sandbox: Drop special-case sandbox console code],
this patch drops the sandbox special-case code in vprintf() that was
missed by Simon at that time.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

compiling U-Boot for avr32 boards shows since
commit 3d1957f0 "dm: i2c: Add support for multiplexed I2C buses"
this warning:

Building current source for 4 boards (4 threads, 8 jobs per thread)
     avr32:  +   atstk1002
+(atstk1002) drivers/i2c/built-in.o: warning: input is not relaxable
     avr32:  +   grasshopper
+(grasshopper) drivers/i2c/built-in.o: warning: input is not relaxable
     avr32:  +   atngw100
+(atngw100) drivers/i2c/built-in.o: warning: input is not relaxable
     avr32:  +   atngw100mkii
+(atngw100mkii) drivers/i2c/built-in.o: warning: input is not relaxable
    0    4    0 /4      0:00:16  : atngw100mkii

Fix it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>

After introduction of CONFIG_SYS_NS16550 these defconfig files were
added and need to be updated.

Signed-off-by: Tom Rini <trini@konsulko.com>

The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.

The dts file is identical to the one submitted upstream.

Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Add defconfig files for the Orangepi Plus and Orangepi PC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

These files are based on the current latest upstream kernel work. The
bus_gates bindings may still change, but for u-boot that does not matter
as we do not (yet) use any clock info from devicetree for sunxi u-boot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.

PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.

The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Based on existing A23/A33 code and the original H3 boot0.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Add initial sun8i H3 support, only uart + mmc are supported for now.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

This is necessary to distinguish between the "dfu-util --detach" and
the "dfu-util --reset" requests.

The default weak implementation of dfu_usb_get_reset() unconditionally
reboots the device, but we want to be able to continue the boot.scr
execution after writing the kernel, fdt and ramdisk to RAM via DFU.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>