Add TI814X EVM board directory, config file, and MAINTAINERS
entry. Enable build.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt to recent omap_hsmmc requirements, Matt re-tested]
Signed-off-by: Tom Rini <trini@ti.com>

Fix the following build error when buildig nitrogen6s1g:

nitrogen6x.c:89:17: error: 'CONFIG_DDR_MB' undeclared (first use in
this function)
nitrogen6x.c:89:17: note: each undeclared identifier is reported only
once for each function it appears in

Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>

This patch adds the configuration file for Snow Board and
defines the same in boards.cfg.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

These boards seem to be unmaintained for quite some time. So lets
remove support for them completely. This also cleans up some
common drivers/files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Guillaume Alexandre <guillaume.alexandre@gespac.ch>
Acked-by: Wolfgang Denk <wd@denx.de>

Adding the build support for dra7xx_evm.
Reusing omap5_evm.h config by moving it to omap5_common.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>

Add new mpc5121e based ac14xx board and a new pinmux config
function for setting individual pinmux bit groups. This
function is used in ac14xx board code.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

This patch adds the a4m2k MPC5200B board port. Its a derivate of
the a3m071 board with only minor changes.

Additionally this patch includes some clean-up changes:
- Remove I2C support from a3m071 as its unused
- Fix/enhance default env variables
- Fix some comments
- Add newly introduced CONFIG_SPL_TARGET to automatically build
  "u-boot-img.bin"
- Fix dtb patching in READ desciption for SPL Linux booting:
  "fdt chosen" needs to get called to patch/create the chosen node.
- Add missing call to spl_board_init():
  Define CONFIG_SPL_BOARD_INIT so that spl_board_init() will get
  called in the SPL version.

Signed-off-by: Stefan Roese <sr@denx.de>

We add USB (RNDIS gadget) SPL support as a separate target.  We need to
pull out YMODEM support in order to be a small enough target binary.

Signed-off-by: Tom Rini <trini@ti.com>

Board and config header files for bf609-ezkit support.

Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>

Add at91sam9g20_2mmc nand boot support. on this board, there is no
dataflash, so disable it

change one commet for at91sam9g20ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

This target will move the environment into SPI flash and documents
the expected layout.  We correct the SPL define for where U-Boot is
and remove an unused define.

Signed-off-by: Tom Rini <trini@ti.com>

The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>

This board is similar to TUXX1 but it has a different sized second
FPGA. Therefore the configuration for the third chipselect is different.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>

This is a preparation for the upcoming kmopti2 board. This board has
also a second fpga on board which is different to the tuxx1 target. But we
want to use the same header file. So remove the config option
KM_DISABLE_APP2 and simply use the board names to distinguish the features.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>

These are no longer used and should be removed.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>

This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

Signed-off-by: Tom Warren <twarren@nvidia.com>

The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD

Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI

Not yet supported:
NAND
RTC
LCD

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>

Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.

So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.

This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>

Enable DCC driver for arm zynq platform to be compiled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.

BSC9132QDS Overview
 --------------------
  2Gbyte DDR3 (on board DDR), Dual Ranki
  32Mbyte 16bit NOR flash
  128Mbyte 2K page size NAND Flash
  256 Kbit M24256 I2C EEPROM
  128 Mbit SPI Flash memory
  SD slot
  USB-ULPI
  eTSEC1: Connected to SGMII PHY
  eTSEC2: Connected to SGMII PHY
  PCIe
  CPRI
  SerDes
  I2C RTC
  DUART interface: supports one UARTs up to 115200 bps for console display

Apart from the above it also consists various peripherals to support DSP
functionalities.

This patch adds support for mainly Power side functionalities and peripherals

Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
	- On-board eCWTAP controller with ETH and USB I/F
	- JTAG/COP 16-pin header for any external TAP controller
	- External JTAG source over AMC to support B2B configuration
	- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
	- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

The following features are supported:
 * 128 MB DDR1 SDRAM
 * DUART
 * SD/MMC Card Socket

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>

This patch adds support for MX23-based Olinuxino board.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

include/configs/tegra-common.h now holds common config options
for Tegra SoCs.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

Add dataflash boot support on at91sam9x5ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM,
Gigabit Ethernet, and eMMC.

This patch supports the following functions:
 - 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

* By a sequence of unfavorable conditions in the config header file, the eb_cpu5282
  booting from  internal stopped after relocation. Blame it is a faulty value of
  CONFIG_SYS_MONITOR_BASE. This patch fix this by replace the wrong condition in
  config header with option in board.cfg

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>

Because calculate_relocation_address now uses the e820 map, it will be able
to avoid addresses over 32 bits and regions that are at high addresses but
not big enough for U-Boot. It also means we can remove the hack which
limitted U-Boot's idea of the size of memory to less than 4GB.

Also take into account the space needed for the heap and stack, so we avoid
picking a very small region those areas might overlap with something it
shouldn't.

Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>

This patch adds support for the a3m071 board based on the
MPC5200.

Signed-off-by: Stefan Roese <sr@denx.de>

The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Signed-off-by: Raphael Assenat <raph@8d.com>
[trini: Squash boards.cfg / MAINTAINERS change into main patch]
Signed-off-by: Tom Rini <trini@ti.com>

Based on previous work by: Alistair Buxton <a.j.buxton@gmail.com>

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Ивайло Димитров <freemangordon@abv.bg>

This adds board support for the Toradex Colibri T20 module.

Working functions:
- SD card boot
- USB boot
- Network
- NAND environment

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>

These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years.  Get rid of the dead
weight.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>

The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.

The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash

In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>