Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers passed to phy_register
function.
This patch was tested on Microblaze architecture.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

RTL8211F needs to enalbe TXDLY for RGMII during
phy initialization, so move it to rtl8211f_config
for early initialization.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

When the ethaddr changes in the env, the hardware should also be updated
so that MAC filtering will work properly without resetting U-Boot.

Also remove the manual calls to set the hwaddr that was included in a
few drivers as a result of the framework not doing it.

Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>

RTL8211F has different registers from RTL8211E.
This patch adds support for RTL8211F PHY which
can be found on Freescale's T1023 RDB board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Signed-off-by: Jagan Teki <jteki@openedev.com>

Certain features we desire require a larger stack than is available by using
iRAM (most notably for us, env_mmc). Relocate the stack to DRAM so that
we can use these features.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

If the SPL is to be used for Falcon mode then we need to make sure the SPL
disable the GSC boot watchdog.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

If the SPL is to be used for Falcon mode then we need to make sure it
configures basic GPIO (iomux, padconf, and default output levels).

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Now that uart and i2c setup functions have been moved to common.c we can
use these and remove code duplication.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Avoid requiring board-model and probe pmic by its i2c address.
This is in preparation for being able to call pmic_setup() from SPL
and not need board type.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Move the code that disables the GSC boot watchdog into gsc.c

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Move shared functions used by both SPL and U-Boot to common.c:
 - setup_iomux_uart() and uart pad config
 - gpio pad config

In the process also moved the following to common.c in preparation for
calling it from the SPL:
 - split i2c setup into a shared function
 - move pmic init to setup_pmic() function to call directly from
   power_init_board()
 - split gpio setup into early (iomux and default pin config)
   and late (output configuration based on env)

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

PCI enumeration occurs early, before we fully configure our GPIO's. Make
sure we steer the MSATA/PCI mux to PCI in board_init to ensure PCI is
selected before enumeration.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

The re-assignment of pcie_rst gpio for GW522x needs to occur earlier, before
the PCI subsystem calls the toggle funciton.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

mxc_serial supports DM so lets use it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Prior to using a gpio a call to gpio_request() should be called to register
it with the gpio subsystem.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Enable U-Boot Driver Model (DM).

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Display what device the SPL will fetch uboot.img from

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

Bootscripts for some distro's such as Android can benefit from knowing
what boot media its script was loaded from.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>

imx6 mmdc supports data rates up to 1066 MT/s, so remove the code handling
higher data rates.

Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>

Having bit 22 cleared in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.

Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.

This was inspired by a patch from Catalin Marinas [1] and also from recent
discussions in the linux-arm-kernel list [2] where Russell King and Rob Herring
suggested that bootloaders should initialize the cache.

[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2010-November/031810.html
[2] https://lkml.org/lkml/2015/2/20/199



Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>

Add emmc boot partition commands to be able to select the boot partition.

Signed-off-by: Soeren Moch <smoch@web.de>

Since there is a default CONFIG_SYS_PBSIZE definition in config_fallbacks.h,
this setting is no longer required in board configurations.

Signed-off-by: Soeren Moch <smoch@web.de>

Only enable graphical output for stdout/stderr (and a usb keyboard for stdin)
when a hdmi device is detected.
Serial console is always enabled for stdin/stdout/stderr.

Signed-off-by: Soeren Moch <smoch@web.de>

Add support for USB OTG host mode. Only high speed devices supported so far
(e.g. usb 2.0 hub required to connect a keyboard).

Signed-off-by: Soeren Moch <smoch@web.de>

Fix the spelling of 'successful'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Cubox-i boards are also supported, so update the README file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Hummingboard dual, dual-lite and solo are now supported via SPL mechanism.

Remove the previous hummingboard support, which does not use SPL and supported
only the solo variant.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

This fixes a regression caused by e25fbe3f
(gw_ventana: Move the DCD settings to spl code)

The clock gating must be setup prior to calling arch_cpu_init(). Without this
booting to SD (directly via eFuse or via bmode) will hang.

Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

 Boards such as imx6q_sabresd might not have mapmem.h as part of
 their common library. This causes a build error if the DEK blob
 command is enabled.

 Fix: make explicit the include of mapmem.h

Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Reviewed-by: Ruchika Gupta <Ruchika.gupta@freescale.com>

Prevent overflow by casting duty_ns to ull first. This bug came up when trying to create a 200 Hz PWM

Signed-off-by: Brecht Neyrinck <bnrn@psicontrol.com>
Acked-by: Heiko <Schocher&lt;hs@denx.de>

Starting USB initialization is useful for those who use Cuboxi/Hummingboard
with HDMI and USB keyboard.

However, when booting without a HDMI connection we can skip the usb
initialization, which makes the boot faster.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>

By making the tqma6_iomuxc_spi() weak, this patch adds the possibility to
add a different function for this SPI configuration. This can be used
by other baseboards, that might have a different SPI setup.

This patch will be used by the upcoming WRU-IV board support which also
uses the TQMa6 SoM.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch fixes the USB EHCI support on the TQMa6 SoM. Additionally
some filesystems are added, included the generic FS commands (e.g.
ls...).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-By: Markus Niebel <Markus.Niebel@tq-group.com>

Configure PAD_ENET_RXD0/RXD1 pads as pull down because these pads are directly
connected to the Atheros 8035/8030 although they should be functional
only in the RMII mode - 8030.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>