The eMMC controller on LD20 or later supports HS-400 mode. It works on
a quick test. Enable it in case somebody may want to use it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Switch over to ADMA from SDMA.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

When the board was originally submitted, it was attempting to use the
ESDHC driver. The board uses the USDHC driver.

Signed-off-by: Carl Gelfand <carl@novtech.com>
Cc: Shawn Guo <shawn.guo@kernel.org> (maintainer:MEERKAT96 BOARD)
Acked-by: Shawn Guo <shawnguo@kernel.org>

This reverts commit 02dc1599

Commit 02dc1599 ("configs: enable sata, eSDHC, USB device module in
T2080QDS")

has some sata defconfig changes to fit support DM mode, Now the driver
will be reverted, So revert it.

Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

s/dtbi/dtb/

Signed-off-by: Jared Baldridge <jrb@expunge.us>

Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.

Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.

Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

Enable HDMI output for Tinker RK3288 board.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

Add mmc device partition 0 as the seat of the environment.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Enable configs to fix USB Host boot mode.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Early cons will be used in uart boot. Enable the same for j721e_r5

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Enable CONFIG_SPL_ETH_SUPPORT to fix ethernet boot support.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>

It's a very rare if at all existing occasion when ARC CPU template
is used as is w/o any changes - in the end it's a beauty and competitive
advantage of ARC cores to be tailored for a particular use-case - and
so it doesn't make a lot of sense to offer template-based "-mcpu" selection.
Given for each and every platform we end-up adding quite a few more flags
it's logical to move "-mcpu" selection to platform's definition as well
which we exactly do here.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Given now nsim_hs38 configuration is usable on QEMU and in QEMU
we have Virtio working perfectly fine the next logical step
is to add support of supported & known to work net & bkl to this
config.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

We don't have yet any brc700 or big-enadian platforms with networking
support to run this particular configuration.

Whenever QEMU for ARC supports arc700 or big-endian targets we may revisit
this one.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Since v2019.06 DesingWare nSIM supports DesignWare UART simulation
and so we may switch from pretty unusual ARC UART to much more standard
DesignWare UART (which in case of U-Boot is just an ordinary 16650 UART).

This among other things makes built dinaries compatible with our other
platforms to name a few: FPGA-based HAPS boards, QEMU and even ZeBU.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Drop PPD_UART_PAD_CTRL since it matches defaults.
Enable DM serial and MXC uart.

Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Remove legacy uart pad and iomux code
Enable DM serial and mxc uart

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Remove legacy iomux setup for fec.
Enable phylib and DM fec.
Use Kconfig for enabling fec.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Add backlight and panel devicetree definitions
Use UCLASS_PANEL to enable backlight via display enable handler
Remove old explicit gpio code for handling backlight
Use cls command to initiate display in HW agnostic manner
Enable DM regulator and pwm

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Enable DM_VIDEO for mx53ppd.
Enable DM_REGULATOR_FIXED and DM_PWM for the backlight.
Remove unused MX53PPD_LCD_POWER.
Remove old (incorrect) setup_iomux_lcd.
Enable backlight via display enable handler.
Use cls command to initiate display in HW agnostic manner.
Modify `failbootcmd' to use lcdputs.

Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>

Remove old (pre-DM) i2c setup code.
Enable DM i2c.
Convert common code to use DM rtc.
Convert common code to read VPD from eeprom partition.
Convert the generic i2c PMIC init code to use the new da9063 driver.

mx53ppd only:
Correct RTC compatible in device tree.
Enable MXC DM i2c driver.
Define CONFIG_SYS_MALLOC_F_LEN so that DM is available in pre-reloc.
Make GPIO banks available during preloc, since initialisation is done
in board_early_init_f().
Add gpio_request() calls to satisfy the DM_GPIO compatibility API.
Remove unused power configuration.

Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>

Convert imx6sabresd PCI to driver model to fix the following warning:

===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================

After the conversion the following commands were used for testing:

=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun  VendorId   DeviceId   Device Class       Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>

Enable DM thermal driver and iMX thermal driver to get accurate
CPU frequency reporting in the boot log.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>

Convert to DM ethernet to prevent board removal.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>

Just move the defconfig entries which are required into the Novena
entry in arch Kconfig, no functional change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>

This patch enables support for CONFIG_OF_BOARD_SETUP in xea defconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

Redundant envs help with assuring better reliability for the system as they
prevent from the situation when envs are stored only in a single place.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

Both CMD_MX_CYCLIC and MX_CYCLIC are in use and defined in Kconfig,
but only the non-CMD version currently does anything. This changes all
usages to prefer the CMD_MX_CYCLIC option (since it's only affecting
addition of the commands), and switches defconfigs using the non-CMD
version to use the CMD version.

Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Tom Rini <trini@konsulko.com>

Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.

This brings additional maintainance effort without a clear
advantage.

Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.

Also remove the SPL related code from the board file.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>

The CONFIG_DM_74X164 symbols should be moved to the defconfig file,
as indicated in the comments.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad
2GB WB IT V1.0A module. They are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports booting from the on-module eMMC only, SDP support is disabled
for now due to missing i.MX 8M Mini USB support.

Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet
- GPIOs
- I2C

Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper

ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.

Boot:
U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)
Normal Boot
Trying to boot from MMC1
NOTICE:  Configuring TZASC380
NOTICE:  RDC off
NOTICE:  BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty
NOTICE:  BL31: Built : 01:11:41, Jan 25 2020
NOTICE:  sip svc init

U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100)

CPU:   Freescale i.MX8MMQ rev1.0 at 0 MHz
Reset cause: POR
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial#
 06535149
Net:   eth0: ethernet@30be0000
Hit any key to stop autoboot:  0
Verdin iMX8MM #

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>

Add basic Presidio G3 engineering board support

Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>

This patch enable mt7622 ethernet support in its defconfig

Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>

Enable TPM2 so that we can use cr50.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This partially reverts changes by commit 2cc393f3
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>