This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port

Currently EMAC2+3 are not working. This will be fixed in a later
release.

Signed-off-by: Stefan Roese <sr@denx.de>

Add maintainer information for the Blackfin boards.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This patch adds support for the AMCC Canyonlands 460EX evaluation
board.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

Signed-off-by: Heiko Schocher <hs@denx.de>

Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Hi,

The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.

Signed-off-by: Michael Schwingen <michael@schwingen.org>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

With serial, NE2000, IDE support. Tested in big-endian mode.
Memory size hard-coded to 128M for now, so don't play with
the -m option.

Signed-off-by: Vlad Lungu <vlad@comsys.ro>

MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
*	       TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
*		       load)

Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
  BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
  DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
  connected to SPI.

Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Add support for Instituto Atlantico's ATUM8548 board

Signed-off-by: robert lazarski <robertlazarski@gmail.com>

Add support for Wind River's SBC8548 reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signed-off by: Andy Fleming <afleming@freescale.com>

update the CREDITS and MAINTAINERS.

Signed-off-by: Dave Liu <daveliu@freescale.com>

Add the MAINTAINER and MAKEALL entries for mpc837xemds

Signed-off-by: Dave Liu <daveliu@freescale.com>

This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

This board never left prototyping state and it
became a millstone round my neck. So remove it.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

These patches add support for the PPC440EPx-based "Korat" board to
U-Boot.  They are based primarily on support for the Sequoia board.

Signed-off-by: Larry Johnson <lrj@acm.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Add all the ATSTK1000 daughterboards to MAINTAINERS along with their
"mother". Also update the entry for ATSTK1000 to be not only about the
AP7000 CPU; it's intended to handle all CPUs in the AT32AP family.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

and reorder the existing 83xx maintainers alpha.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Add support for Wind River's SBC8641D reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>

Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA

Changes:

- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
   DV_EVM. Can't check if it works on SONATA, don't have a board any more,
   but it at least compiles.

Here is an excerpt from session log on SCHMOOGIE...

U-Boot 1.2.0-g6c33c785-dirty (Aug  7 2007 - 13:07:17)

DRAM:  128 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY   : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >

Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>

This series of patches adds support for 2 boards from Netstal Maschinen.

The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.

The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.

The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.

This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>