- Jul 11, 2011
-
-
York Sun authored
Add this option to allow boards to override the default read-to-write turnaround time for better performance. Signed-off-by:York Sun <yorksun@freescale.com>
-
Ramneek Mehresh authored
Resolve P1020 second USB controller multiplexing with eLBC - mandatory to mention USB2 in hwconfig string to select it over eLBC, otherwise USB2 node is removed - works only for SPI and SD boot Signed-off-by:
Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by:
Kumar Gala <galak@kernel.crashing.org>
-
Ramneek Mehresh authored
Specify hwconfig usage for USB mode and phy change Signed-off-by:
-
Ramneek Mehresh authored
Modify support for USB mode fixup: - Add common support for USB mode and phy type device tree fix-up for all USB controllers mentioned in hwconfig string - Fetch USB mode and phy type via hwconfig; if not defined in hwconfig, then fetch them from env Signed-off-by: -
Roy Zang authored
The P1023RDS board is the reference board for the P1023 SoC. Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe, UART, I2C, etc. Signed-off-by:
Roy Zang <tie-fei.zang@freescale.com> Signed-off-by:
Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by:
Chunhe Lan <Chunhe.Lan@freescale.com> Signed-off-by:
Lei Xu <B33228@freescale.com> Signed-off-by:
-
York Sun authored
If DDR initialziation uses a speed table and the speed is not matched, print a warning message instead of silently ignoring. Signed-off-by:
-
York Sun authored
Allow overriding RCW for all RDIMM, not only quad-rank ones. Signed-off-by:
-
York Sun authored
Checking width before setting DDR controller. SPD for DDR1 and DDR2 has data width and primary sdram width. The latter one has different meaning for DDR3. Signed-off-by:
-
York Sun authored
In case of empty SPD or checksum error, fallback to raw timing on supported boards. Signed-off-by:
-
York Sun authored
We used to have fixed parameters for soldered DDR chips. This patch introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing data from DDR chip datasheet, implemneted in board-specific files or header files. Signed-off-by:
-
Felix Radensky authored
On P1022/P1013 second USB controller is muxed with second Ethernet controller. The current code to enable second USB fails to properly clear pinmux bits used by ethernet. As a result, Linux freezes when this controller is used. This patch fixes the problem. Signed-off-by:
Felix Radensky <felix@embedded-sol.com> Signed-off-by:
-
York Sun authored
Adding byte 32 and 33 Signed-off-by:
-
York Sun authored
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit DDR devices. Signed-off-by:
-
York Sun authored
Only use DDR DIMM part number if SPD has valid length, to prevent from display garbage in case SPD doesn't cover these fields. Signed-off-by:
-
York Sun authored
If the bus width is 32-bit, burst chop should be disabled and burst length should be 8. Read from SPD or other source to determine the width. Signed-off-by:
-
Timur Tabi authored
Signed-off-by:
Timur Tabi <timur@freescale.com> Signed-off-by:
-
Shaohui Xie authored
When booting from NAND we get the environment and FMan ucode from NAND. Signed-off-by:
Shaohui Xie <b21989@freescale.com> Signed-off-by:
-
Kumar Gala authored
The P2041 is similar to P2040, however has a 10G port and backside L2 Signed-off-by: -
Mingkai Hu authored
Add P2040 SoC specific information: * LIODN setup * Portal configuration * etc Signed-off-by:
Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by:
-
Kumar Gala authored
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also rearrange setting of _tbl_sz variables to utilize existing ifdef protection for things like FMAN. Also add protection around setup_portals() call in corenet_ds board code. Signed-off-by: -
Ramneek Mehresh authored
Add CONFIG_HAS_FSL_DR_USB macro for P1020RDB Signed-off-by:
-
Kumar Gala authored
Add ifdef protection in LBC code to handle the case in which CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a build. Signed-off-by: -
Kumar Gala authored
Add ifdef protection in LAW & TLB code to handle the case in which CONFIG_SYS_BMAN_MEM_PHYS or CONFIG_SYS_QMAN_MEM_PHYS arent defined for a build. Signed-off-by:
-
- Jul 07, 2011
-
-
Bill Cook authored
On a 8308 based board it was found that the PEX_GLK_RATIO register (programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This was tracked to the fact that the pci express clock frequency was not being assigned to the pciexp1_clk entry in the global data structure in file arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in 'do_clocks' command. Signed-off-by:
Bill Cook <cook@isgchips.com> Signed-off-by:
Kim Phillips <kim.phillips@freescale.com>
-
Timur Tabi authored
Remove an empty board_early_init_f() from the MPC8323ERD and MPC360ERDK boards. Signed-off-by:
-
Andre Schwarz authored
Includes board config file, documentation, maintainer and boards.cfg entries, and board specific files in vendor dir. Signed-off-by:
Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by:
-
Andre Schwarz authored
CPO value and driver strength settings are board specifc. Also allow SPD data fetch from any accessible I2C EEPROM. Signed-off-by:
-
Andre Schwarz authored
Signed-off-by:
-
Andre Schwarz authored
Running on mpc837x without CONFIG_FSL_ESDHC leads to i2c1_clk not being set at all. It is bound to clock of encryption module. fix this. Signed-off-by:
-
Ira W. Snyder authored
Commit 359ec493 broke support for the Freescale DMA engine on the 83xx parts. This is due to using registers which do not exist on 83xx. Remove the attribute register accesses from the 83xx build. Signed-off-by:
Ira W. Snyder <iws@ovro.caltech.edu> Cc: York Sun <yorksun@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by:
-
- Jul 04, 2011
-
-
Simon Guinot authored
This patch add support for the Network Space v2 board and parents, based on the Marvell Kirkwood 6281 SoC. This include Network Space (Max) v2 and Internet Space v2. Additional information is available at: http://lacie-nas.org/doku.php?id=network_space_v2 Signed-off-by:
Simon Guinot <sguinot@lacie.com>
-
Valentin Longchamp authored
This adds support for the keymile Kirkwood BEC portl2 board. This board relies on the km_arm (km_kirkwood) BEC. The egiga driver is configured for a 100M full-duplex, A/N off connnection to the backplane. This board has always ethernet present, because it is connected to the marvell switch similar to mgcoge3un. The reset_phy functionality is also the same to mgcoge3un. Signed-off-by:
Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by:
Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Heiko Schocher <hs@denx.de>
-
Holger Brunck authored
suen3 and suen8 were in first HW version quite different, but now they are from a u-boot point of view similar. So these two boards can use the same header file. Other keymile boards differ only in the usage of the PCI interface. Therefore a target km_kirkwood_pci was introduced. All targets use the same header file. Signed-off-by:
-
Valentin Longchamp authored
The phy is also configured with "RGMII clock transitions when data stable" and "Class A driver for the direct backplane connection". Signed-off-by:
-
Valentin Longchamp authored
This is defined for all km_kirkwood boards and was not used up to now. This value was the same for all boards but it could be changed for some boards (and thus needs to be defined for every board). Signed-off-by:
-
Holger Brunck authored
CONFIG_ENV_SIZE for NAND was later in this file overwritten because we have the environment in i2c eeprom, so remove this define. Signed-off-by:
-
Holger Brunck authored
commit 010a958b (arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h) breaks building keymile arm targets, when u-boot.kwb tries to generate the binary with mkimage. A simple make <board> or MAKEALL succeeded because it don't try to build the kirwood binary at the end. Due this commit we use the CONFIG_SYS_KWD_CONFIG from the arch-kirkwood/config.h and it was removed from the board config. But it was forgotten to include the header. Now the header is included in km_arm.h. Some other defines were obsolete due to this include, these are also removed in this commit. Signed-off-by: -
Holger Brunck authored
Some boards e.g. keymile arm boards have CONFIG_CMD_I2C switched on but they use soft i2c on kirkwood. So don't switch CONFIG_I2C_MVTWSI on in this case. Signed-off-by: -
Jens Scharsig authored
* Fix compiler error for cpu at91sam9, if lowlevel init is enabled * use correct ATMEL_ name scheme to define ATMEL_BASE_SDRAMC Signed-off-by: Jens Scharsig
-
Andreas Bießmann authored
This patch removes the board implemenatation for flash driver which can now safely switched to the common cfi driver. Compile tested for all atstk100x boards, runtime tested on atstk1002. Signed-off-by:Andreas Bießmann <biessmann@corscience.de>
-
