This can be useful for generic scripts. For example, rather than hard-
coding a script to ext2load tegra-harmony.dtb, it could load
${soc}-${board}.dtb and hence not need adjustments to run on multiple
boards.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

loop_count runs down from 10000, so the correct condition to error out
is ==0.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren.nvidia@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

This is needed as a prerequisite for Tegra USB ULPI support
within U-Boot.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

The Tamonten Evaluation Carrier is an evaluation board for the Tamonten
processor board. More information is available here:

	http://www.avionic-design.de/en/products/nvidia-tegra-tamonten-system-en/nvidia-tegra-tamonten-evboard-en.html



Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

GPIO PI6 can be used to obtain the write-protect status of an SD card
inserted into the SD slot.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

The PI4 GPIO is used on Tamonten to reset carrier board peripherals.
Power sequencing hardware on the carrier pulls the reset low before
powering up the Tegra, and the CPU is supposed to signal readiness,
and therefore bring peripherals out of reset by pulling PI4 high.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Device tree support is required for working USB host support, which in
turn enables ethernet support.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

Device tree support is required for working USB host support, which in
turn enables ethernet support.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

This commit uses the common Tegra board implementation instead of
duplicating a lot of the code. In addition, the Plutux and Medcom
specific board files can be removed as the MMC/SD setup is common
among all Tamonten-based boards.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>

this is for a prototyping board

vendor/product ids have been added to
http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs



Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>

This reverts commit fa042186.
It causes build warnings like this:
cpu.c:48:1: warning: -fstack-usage not supported for this target
[enabled by default]

Signed-off-by: Wolfgang Denk <wd@denx.de>

Commit 896bbb53 "fdt: avoid bad MAKEALL status" added logic to capture
the result code from dtc by echoing $? to stdout and capturing it using
$(). However, dtc emits some diagnostics to stderr and some to stdout.
The diagnostics send to stdout ended up getting captured via $() rather
than being echo'd to the user. This caused those diagnostics to be passed
to the exit command, which would then fail with the following cryptic
error message:

    /bin/sh: line 1: exit: too many arguments

Solve this by redirecting all dtc output to stderr so that $() does not
capture it. This allows the user to see the actual error message from dtc.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: albert.u.boot@aribaud.net
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>

This warning was introduced in 436da3cd "ext2load: increase read
speed":

ext2fs.c: In function 'ext2fs_read_file':
ext2fs.c:458:19: warning: 'blocknxt' may be used uninitialized in this function [-Wuninitialized]

this change makes it go away.

Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mkenvimage does not build due to missed os_support.o and unsupported
file modes S_IRGRP S_IWGRP.
Tested with mingw 4.2.1 on ubuntu 12.04.

Signed-off-by: Vladimir Yakovlev <nagos@inbox.ru>

commit "net: use common rand()/srand() functions" introduced the following
build warning on the current u-boot-arm tree:

$ ./MAKEALL MPC8313ERDB_66
Configuring for MPC8313ERDB_66 - Board: MPC8313ERDB, Options: SYS_66MHZ
   text	   data	    bss	    dec	    hex	filename
 271988	  13976	  41768	 327732	  50034	./u-boot
In file included from bootp.c:15:0:
net_rand.h: In function 'srand_mac':
net_rand.h:40:2: warning: implicit declaration of function 'srand' [-Wimplicit-function-declaration]

adding this dependency fixes it.

Cc: Michael Walle <michael@walle.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Michael Walle <michael@walle.cc>

Drop mdelay() macros since we already have a common mdelay() func.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

* 'master' of git://git.denx.de/u-boot-arm

: (212 commits)
  ARM: cache: Move the cp15 CR register read before flushing the cache.
  ARM: introduce arch_early_init_r()
  PXA: Enable CONFIG_PREBOOT on zipitz2
  ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
  No need to define CONFIG_ARCH_CPU_INIT.
  add new board vl_ma2sc
  MTD: SPEAr SMI: Add write support for length < 4 bytes
  i2c: designware_i2c.c: Add support for the "i2c probe" command
  rtc/m41t62: Add support for M41T82 with HT (Halt Update)
  SPL: ARM: spear: Add SPL support for SPEAr600 platform
  Makefile: Add u-boot.spr build target (SPEAr)
  SPL: ARM: spear: Remove some objects from SPL build
  SPL: lib/Makefile: Add crc32.c to SPL build
  SPL: common/Makefile: Add image.c to SPL build
  arm: Don't use printf() in SPL builds
  GPIO: Add SPEAr GPIO driver
  net: Multiple updates/enhancements to designware.c
  cleanup/SPEAr: Define configuration flags more elegantly
  cleanup/SPEAr: Remove unnecessary parenthesis
  SPEAr: Correct SoC ID offset in misc configuration space
  SPEAr: explicitly select clk src for UART
  SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
  SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
  SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
  SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
  SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
  SPEAr: Enable dcache for fast file transfer
  SPEAr: Enable autoneg for ethernet
  SPEAr: Enable udc and usb-console support only for usbtty configuration
  SPEAr: Enable usb device high speed support
  SPEAr: Initialize SNOR in early_board_init_f
  SPEAr: Change the default environment variables
  SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
  SPEAr: Add configuration options for spear3xx and spear6xx boards
  SPEAr: Add basic arch related support for SPEAr SoCs
  SPEAr: Add interface information in initialization
  SPEAr: Add macb driver support for spear310 and spear320
  SPEAr: Configure network support for spear SoCs
  SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
  SPEAr: Eliminate dependency on Xloader table
  SPEAr: Fix ARM relocation support
  st_smi: Fixed page size for Winbond W25Q128FV flash
  st_smi: Change timeout loop implementation
  st_smi: Fix bug in flash_print_info()
  st_smi: Change the flash probing method
  st_smi: Removed no needed dependency on ST_M25Pxx_ID
  st_smi: Fix smi read status
  st_smi: Move status register read before modifying ctrl register
  st_smi: Read status until timeout happens
  st_smi: Enhance the error handling
  st_smi: Change SMI timeout values
  st_smi: Return error in case TFF is not set
  st_smi: Add support for SPEAr SMI driver
  mtd/NAND: Remove obsolete SPEAr specific NAND drivers
  SPEAr: Configure FSMC driver for NAND interface
  mtd/NAND: Add FSMC driver support
  arm/km: remove calls to kw_gpio_* in board_early_init_f
  arm/km: add implementation for read_dip_switch
  arm/km: support the 2 PCIe fpga resets
  arm/km: skip FPGA config when already configured
  arm/km: redefine piggy 4 reg names to avoid conflicts
  arm/km: cleanup km_kirkwood boards
  arm/km: enable BOCO2 FPGA download support
  arm/km: remove portl2.h and use km_kirkwood instead
  arm/km: convert mgcoge3un target to km_kirkwood
  arm/km: add kmcoge5un board support
  arm/km: add kmnusa board support
  arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
  cm-t35: fix incorrect NAND_ECC layout selection
  ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
  ARM: OMAP4/5: Move USB pads to essential list.
  ARM: OMAP4/5: Move USB clocks to essential group.
  ARM: OMAP4/5: Move gpmc clocks to essential group.
  ARM: OMAP4+: Move external phy initialisations to arch specific place.
  omap4: Use a smaller M,N couple for IVA DPLL
  da850/omap-l138: Enable auto negotiation in RMII mode
  omap: am33xx: accomodate input clocks other than 24 Mhz
  omap: emif: fix bug in manufacturer code test
  omap: emif: deal with rams that return duplicate mr data on all byte lanes
  OMAP4+: Force DDR in self-refresh after warm reset
  OMAP4+: Handle sdram init after warm reset
  ARM: OMAP3+: Detect reset type
  arm: bugfix: Move vector table before jumping relocated code
  Kirkwood: Add support for Ka-Ro TK71
  arm/km: use spi claim bus to switch between SPI and NAND
  arm/kirkwood: protect the ENV_SPI #defines
  ARM: don't probe PHY address for LaCie boards
  lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
  lacie_kw: fix SDRAM banks number for net2big_v2
  Kirkwood: add lschlv2 and lsxhl board support
  net: add helper to generate random mac address
  net: use common rand()/srand() functions
  lib: add rand() function
  kwboot: boot kirkwood SoCs over a serial link
  kw_spi: add weak functions board_spi_claim/release_bus
  kw_spi: support spi_claim/release_bus functions
  kw_spi: backup and reset the MPP of the chosen CS pin
  kirkwood: fix calls to kirkwood_mpp_conf
  kirkwood: add save functionality kirkwood_mpp_conf function
  km_arm: use filesize for erase in update command
  arm/km: enable mii cmd
  arm/km: remove CONFIG_RESET_PHY_R
  arm/km: change maintainer for mgcoge3un
  arm/km: fix wrong comment in SDRAM config for mgcoge3un
  arm/km: use ARRAY_SIZE macro
  arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
  arm/km: add piggy mac adress offset for mgcoge3un
  arm/km: add board type to boards.cfg
  AT91SAM9*: Change kernel address in dataflash to match u-boot's size
  ATMEL/PIO: Enable new feature of PIO on Atmel device
  ehci-atmel: fix compiler warning
  AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
  Atmel : usb : add EHCI driver for Atmel SoC
  Fix: AT91SAM9263 nor flash usage
  Fix: broken boot message at serial line on AT91SAM9263-EK board
  i.MX6 USDHC: Use the ESDHC clock
  mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
  i.MX28: Add function to adjust memory parameters
  mx28evk: Fix PSWITCH key position
  mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
  mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
  imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove unused CONFIG_MII_GASKET
  mx6: Avoid writing to read-only bits in imximage.cfg
  m28evk: use same notation to alloc the 128kB stack
  ...

Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-mpc85xx

:
  powerpc/mpc85xx: Fix Handling the lack of L2 cache on P2040/P2040E
  powerpc/mpc85xx: Workaround for erratum CPU_A011
  powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
  powerpc/P4080: Check SVR for CPU22 workaround
  lib/powerpc: addrmap_phys_to_virt() should return a pointer
  powerpc/85xx: clean up P1022DS board configuration header file
  powerpc/85xx: fdt_set_phy_handle() should return an error code
  powerpc/85xx: minor clean-ups to the P2020DS board header file
  powerpc/p1010rdb: add readme document for p1010rdb
  powerpc/mpc85xx:NAND_SPL:Avoid IFC/eLBC Base address setting
  powerpc/mpc85xx:Add debugger support for e500v2 SoC
  powerpc/85xx:Fix NAND code base to support debugger
  powerpc/85xx:Make debug exception vector accessible
  powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
  PATCH 1/4][v4] doc:Add documentation for e500 external debugger support
  powerpc/p1010rdb: update mux config of p1010rdb board
  powerpc/mpc85xx:Add BSC9131 RDB Support
  powerpc/mpc85xx:Add BSC9131/BSC9130/BSC9231 Processor Support
  powerpc/85xx: Add USB device-tree fixup for various platforms

Signed-off-by: Wolfgang Denk <wd@denx.de>

The following is the cleanup sequence in arch/arm/cpu/armv7/cpu.c

int cleanup_before_linux(void)
{
 ...
 ...
 dcache_disable();
 v7_outer_cache_disable();
 invalidate_dcache_all();
}

 1) invalidate_dcache_all call expects that all the caches has been
 flushed, invalidated and there are no dirty entries prior to its
 execution.  In the above sequence dcache_disable() flushes, invalidates
 the caches and turns off the  mmu. But after it cleanups the cache
 and before the mmu is disabled  there is a cp_delay() function which
 has STR instruction. On certain cores like the cortex-a15, cache hit
 and a write can happen to a cache line even when the dcache is
 disabled. So the above mentioned STR instruction creates a dirty entry
 after cleaning. The mmu gets disabled after this.

 2) invalidate_dcache_all invalidates the cache lines. Again on
 cores like cortex-a15, invalidate instruction flushes the dirty
 line as well. So some times the dirty line from sequence 1
 can corrupt the memory resulting in a crash.

 Fixing this by moving the get_cr() and cp_delay() calls before
 cleaning up the cache, thus avoiding the dirty entry.

Signed-off-by: R Sricharan <r.sricharan@ti.com>

Introduce arch_early_init_r() function, which can be useful for doing
early initialization after relocation has happened.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Marek Vasut <marex@denx.de>

No need to define CONFIG_ARCH_CPU_INIT.

All mx28 based boards should use arch_cpu_init().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>

All mx6 based boards should use arch_cpu_init().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>

* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>

Needed for redundant environment for example.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>

i2c_probe() is changed to reinit the i2c bus upon read failure.
This is naturally the case upon i2c bus probing.

Also, some printf messages upon read failure are removed. As they
would interfere with the "i2c probe" command.

Additionally, i2c_set_bus_speed() now returns 0, so that the
"i2c speed" command can be used.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>

Add support for the M41T82 RTC to the m41t62 driver. The only
difference that needs to be handled by this driver, is to
clear the HT (Halt Update) bit upon reset. This bit is not
used on the M41T62, so its save to clear this bit always.

The M41T82 support will be used by the X600 (SPEAr600)
board support.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch adds SPL support for SPEAr600. Currently only SNOR
(Serial NOR) flash support is included. Other boot devices
(NAND, MMC, USB ...) may be added with later patches.

Tested on the STM SPEAr600 evaluation and x600 SPEAr600 boards.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>

On x600 (SPEAr600) U-Boot is appended to U-Boot SPL. Both images are
created using mkimage (crc etc), so that the ROM bootloader can check
its integrity. Padding needs to be done to the SPL image (with
mkimage header) and not the binary. Otherwise the resulting image
which is loaded/copied by the ROM bootloader to SRAM doesn't fit.
The resulting image containing both U-Boot images is called u-boot.spr.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>

This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).

Signed-off-by: Stefan Roese <sr@denx.de>

This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).

Signed-off-by: Stefan Roese <sr@denx.de>

raise() likes to call printf() if it is available, but in SPL builds it
either is not available, or adds a large chunk to the resulting image
size.

So don't call it even if it is available.

This change reduces SPL size from 10KB to 6.3KB on hawkboard, for
example, using generic relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>

Tested on x600 (SPEAr600).

Signed-off-by: Stefan Roese <sr@denx.de>

This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:

- Don't init MAC & PHY upon startup. This causes a delay, waiting for
  the auto negotiation to complete. And we don't want this delay to
  always happen. Especially not on platforms where ethernet is not
  used at all (e.g. booting via flash).
  Instead postpone the MAC / PHY configuration to the stage, where
  ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
  for example on the X600 board, where the Vitesse PHY needs to be
  configured for GMII mode.
  This board specific PHY init is done via the function
  designware_board_phy_init(). And this driver now adds a weak default
  which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
  link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>

In SPEAr, some of the configuration flags eg. CONFIG_SPEAR_EMI, were given value
"1", which isn't required. Define the flags without assigning any value

Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

In SPEAr configuration files, unnecessary paranthesis are used in some
\#defines. Remove them as they serve no purpose

Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

SoC Core ID offset is 0x30 in miscellaneous configuration address
space. It was wrongly mentioned as periph2 clk enable.

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>