Newly added cm_t335 was missed in commit 47ed5dd0 which
made ARM targets produce full ELF files. Fix its linker
script.

This change is binary-invariant when only .dynsym, .dynstr,
.dynamic, .plt, .interp and .gun sections are declared.

Sections .hash, .got.plt, .dynbss and .ARM.exidx are also
declared so that their (unused) content is moved out of the
u-boot binary.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>

Add support for the bcm28155_ap reference board.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add support for the Kona SDHCI found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add support for the Kona I2C controller found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add support for the Kona GPIO controller found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Add bcm281xx architecture support code including a clock framework and
chip reset.  Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>

Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as
much as possible. This will aid in a future patch which will create a
common header e.g. config_distro_bootcmd.h.

While at it, enable booting from extlinux.conf using the sysboot command.

The iteration and componentization currently makes a little more sense
for Tegra than RPi, but I'd still like to keep the two as similar as
possible. USB and networking support is coming to the RPi in due course,
and it'll all make more sense then anyway.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

The function pll_sigma_delta_val uses "float" data which is not correct.
The exact "why" of this mangling is lost to history, but this changes us
to equivalent non-FP math to get the same results.

Reported-by: Wolfgang Denk <wd@denx.de>
Acked-by: Matt Porter <mporter@linaro.org>

Commit 6789e84e (i2c, omap24xx:
convert driver to new mutlibus/mutliadapter framework) intended to
make I2C driver compatible with latest changes. It unfortunately has
had a impact on size on SPL as well. For example on SDP4430,
32032 bytes before/MLO
35416 bytes after/MLO

With this mentioned commit, MLO stops booting on SDP4430 as only 32K
is accessible for non-secure (bootloader) s/w on GP devices and the size
increase to 56K fails boot.

On the latest u-boot commit e7be1822,
MLO is now at size 35592 bytes, However, I2C is not necessary for SPL
to function as we use SR_I2C for controlling the PMIC.
Disabling I2C reduces MLO to 32224 bytes which allows
OMAP4 GP platform to boot up.

Since this is common for all OMAP4 platforms, remove the need for I2C
for SPL builds in the common config.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sricharan R <r.sricharan@ti.com>

Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Tom Rini <trini@ti.com>

Signed-off-by: Tom Rini <trini@ti.com>

With CONFIG_SYS_BOOTMAPSZ defined, recent Linux kernel booting
results in this error:

   Booting using the fdt blob at 0x81f00000
   Loading Kernel Image ... OK
ERROR: Failed to allocate 0x1189d bytes below 0x80004000.
device tree - allocation error
FDT creation failed! hanging...### ERROR ### Please RESET the board ###

Removing this define solves this issue.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>

commit 194dd74a
(DRA7: add ABB setup for MPU voltage domain)

Made an offset typo error by using 0x4A003B24 as the efuse offset
for OPP_NOM. As per TI documentation, 0x4A003B24 is for OPP_OD, and
0x4A003B20 is for OPP_NOM. Fix the same.

Reported-by: Praveen Rao <prao@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>

DDR timings were broken since 47abc3df
for PandaBoard EA1.

Signed-off-by: Janne Grunau <j@jannau.net>

Patch allows to load a script at the startup from MMC.

Signed-off-by: Stefano Babic <sbabic@denx.de>

New hardware version cannot recognize the SD-Card
because the SYS_NRESWARM, set as GPIO, does not
guarantee the required reset time.
Change the pin function back to enable the
SYS_NRESWARM signal driven by the SOC.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Patch contains the same fixes as commit
4b9b2c30
(missing CONFIG_OMAP3_GPIO_2) and commit
f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC).
Same issues are relevant for the mcx board, too.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on tao3530. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>

Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>

Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB
Motherboard, using TI's AM3352 SoC.

Most of code is derived from TI's AM335x_EVM

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: trini@ti.com

Adds support for Bernecker & Rainer Industrieelektronik GmbH T-Series
Motherboard, using TI's AM3352 SoC.

Most of code is derived from TI's AM335x_EVM

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>

This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.

[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354



Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>

The Pi has no flash to store an environment in the usual fashion. However,
the user may wish to customize the environment. We know that the SD card
must be present, since that's where the boot ROM has loaded U-Boot from.
So, load uEnv.txt from there early during boot. This allows the user to
e.g. customize boot_targets, in order to automatically select network
boot.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

Modify the rpi_b board to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the rpi_b.h.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

pxe.c provides both the "pxe" command which relies on a network, and the
"sysboot" command which doesn't. Fix the file to compile when network
support isn't enabled. This is useful e.g. on the Raspberry Pi which has
no network support yet, but will soon support the sysboot command.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.

Signed-off-by: Tom Rini <trini@ti.com>

In Kbuild, every makefile must have non-empty obj- or obj-y.
Otherwise, built-in.o will not be created and the link stage
will fail.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

There is a strange comment in fit_image_load().
This function can be used for loading Kernel Image, FDT
as well as ramdisk.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>

If the whole code is surrounded by #ifdef(CONFIG_ ) .. #endif,
it should be moved to Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

CONFIG_SYS_GBL_DATA_SIZE is not used any more.
The size of struct "global_data" is automatically calculated
by asm-offsets. (See lib/asm-offsets.c)

GENERATED_GBL_DATA_SIZE should be used instead of
CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

It is convenient to have all device trees on the same SoC compiled.
It allows for later easy repackaging without the need to re-run
the make file.

  - Build device trees with the same SoC under arch/$(ARCH)/dts

  - Copy the one specified by CONFIG_DEFAULT_DEVICE_TREE or
    DEVICE_TREE=... to dts/dt.dtb

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.

I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.

For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.

This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Useful rules in scripts/Makefile.lib allows us to easily
generate a device tree blob and wrap it in assembly code.

We do not need to parse a linker script to get output format and arch.

This commit deletes ./u-boot.dtb since it is a copy of dts/dt.dtb.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

- Delete fs.xml from DOCBOOKS to fix an error.
     Commit e3ff797c added fs.xml to DOCBOOKS
     but missed to add doc/DocBook/fs.tmpl.
  - Fix the location of include guard in include/linker_lists.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Abraham Varricatt <abraham.varricatt@vvdntech.com>
Acked-by: Simon Glass <sjg@chromium.org>