This patch adds a driver for the following smsc network controllers:
LAN9115
LAN9116
LAN9117
LAN9215
LAN9216
LAN9217

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds an i2c driver for Freescale i.MX processors

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Add support to the Freescale I2C driver (fsl_i2c.c) for setting and querying
the I2C bus speed.  Current 8[356]xx boards define the CFG_I2C_SPEED macro,
but fsl_i2c.c ignores it and uses conservative value when programming the
I2C bus speed.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Add the Freescale on-chip SATA controller driver to u-boot,
The SATA controller is used on the 837x and 8315 targets,
The driver can be used to load kernel, fs and dtb.

The features list:
- 1.5/3 Gbps link speed
- LBA48, LBA28 support
- DMA and FPDMA support
- Two ports support

Signed-off-by: Dave Liu <daveliu@freescale.com>

add simple libata support in u-boot

Signed-off-by: Dave Liu <daveliu@freescale.com>

original ata_piix driver is using IDE framework, not real
SATA framework. For now, the ata_piix driver is only used
by x86 sc520_cdp board. This patch makes the ata_piix driver
use the new SATA framework, so

- remove the duplicated command stuff
- remove the CONFIG_CMD_IDE define in the sc520_cdp.h
- add the CONFIG_CMD_SATA define to sc520_cdp.h

Signed-off-by: Dave Liu <daveliu@freescale.com>

move the sata.h from include/ to drivers/block/ata_piix.h

Signed-off-by: Dave Liu <daveliu@freescale.com>

move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.

Signed-off-by: Dave Liu <daveliu@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

The default settings for RTC DS1337 keeps the OSC
output, 32,768 Hz, on. This add CFG_RTC_DS1337_NOOSC to
turn it off.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>

Signed-off-by: Wolfgang Denk <wd@denx.de>

RTL8211B sets link state register after autonegotiation complete,
so with bootdelay=0 RTL8211B will report lack of the link.

To fix this, we should wait for aneg to complete, even if the
link is currently down.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

This patch adds basic support for Broadcom BCM5481 PHY.

RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is
Peter Barada <peterb@logicpd.com>.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

PHY drivers will use it to setup software delay between RXD and RXC
signals.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards.  A small firwmare must be uploaded to its on-board memory
before it can be enabled.  This patch adds the code which uploads firmware
(but not the firmware itself).

Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs.  The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array
using a NOR Flash interface. This on-chip integration enables system designers
to reduce external system logic and use high-density NAND Flash
in applications that would otherwise have to use more NOR components.

Flex-OneNAND enables users to configure to partition it into SLC and MLC areas
in more flexible way. While MLC area of Flex-OneNAND can be used to store data
that require low reliability and high density, SLC area of Flex-OneNAND
to store data that need high reliability and high performance. Flex-OneNAND
can let users take advantage of storing these two different types of data
into one chip, which is making Flex-OneNAND more cost- and space-effective.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

AX88796L is device of NE2000 compatible.
This patch support AX88796L ethernet device.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

There are more devices of the NE2000 base.
A present code is difficult for us to support more devices.
To support more NE2000 clone devices, separated the function.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The Blackfin on-chip MAC driver was being managed in the BF537-STAMP board
directory, but it is not board specific, so relocate it to the drivers dir
so that other Blackfin ports can utilize it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the "ssync" instruction may have hardware anomalies associated with
it, have the smc91111 driver use the SSYNC macro rather than invoking it
directly.  We workaround all the anomalies via this macro.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

If the LWMON5 config has SYSMON POST among CONFIG_POSTs which may be
run on the board, then the SYSMON POST controls the display backlight
(doesn't switch backlight ON if POST FAILED, and does switch the
backlight ON if PASSED).

If not, then the video driver controls the display backlight (just
switch ON the backlight upon initialization).

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>

In current source code, when the device number of PCI is 0, process PCI
bridge without fail. However, when the device number is 0, it is not PCI
always bridge. There are times when device of PCI allocates.

When CONFIG_PCI_SKIP_HOST_BRIDGE is enable, this problem is solved when
use this patch.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Stefan Roese <sr@denx.de>

Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
  0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
      and so on).

The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.

The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>

With this patch we don't need that many #ifdef's in the code. It moves
the subtraction into the macro and defines a NOP-macro when
CONFIG_FLASH_SHOW_PROGRESS is not defined.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Tor Krill <tor@excito.com>

This patch adds CFG_OHCI_USE_NPS to the common USB-OHCI driver. This
way a board just needs to define this new option to enable the "force
NoPowerSwitching mode" instead of adding new CPU/architecture defines
to the USB source itself.

This new option will be used first with the new AMCC 460EX Canyonlands
board port, which will be posted in a few days.

This patch also fixes a small compilation problem when DEBUG is enabled.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch add support for the STM M41T62 RTC. It is used and tested
on the AMCC Canyonlands 406EX platform.

Signed-off-by: Stefan Roese <sr@denx.de>

When rtl_recv() of rtl8169 is called, OWNbit of status register
is not enable occasionally.
rtl_recv() doesn't work normally when the driver doesn't do
appropriate processing.
This patch fix this problem.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.

Signed-off-by: Timur Tabi <timur@freescale.com>

erratum 5.6 states the autoneg completion bit is functional only if the
autoneg bit is asserted.

This fixes any secondarily-issued networking commands on non-gigabit
links on the mpc8360 mds board.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

When the LM75 temperature sensor measures a temperature below 0 C, the
current driver does not perform sign extension, so the result returned is
256 C too high.  This patch fixes the problem.

Signed-off-by: Larry Johnson <lrj@acm.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>